T. J. Snow > Supplies > Chillers > 12.5 Ton Chiller
A 12.5 Ton Schreiber Chiller

12.5 Ton Chiller

Schreiber Model 1250 AC
(Air Cooled)

Need another size?

Need to figure out what size you need?

Do you know why you should have a chiller if you are resistance welding?

Features:

The unit is rated at the American Refrigeration Institute's National Standard of 95° F ambient and 44° F chilled water.
Energy Saving Design-- The unit will cycle on and off with varied load demands. No hot gas bypass.
Closed loop system eliminates contamination of the water system by recycling the water in a contaminant free flow path.
The Water Pump is bronze or stainless steel, and contaminate free.
Utilizes environmentally friendly R-22 refrigerant.
Ethylene glycol is not required for normal operating conditions. The unit will NOT be damaged due to an accidental freeze up.
Uses a world-renowned Tecumseh^TM compressor.
The Condenser is designed to allow full capacity at higher temperatures.
Energy Saving Design which does not use hot gas bypass.
Epoxy polyester powder coat finish is highly durable and environmentally responsible.
Time proven Schreiber Engineering name, and record of Superior Quality. In business since 1958.
Tested and approved by ETL Testing Laboratories, Inc.

Note about the Tonage Ratings:
The TrueTon^TM label assures that every Schreiber Chiller meets or exceeds its stated BTU performance as measured by the American Refrigeration Institute standard testing methods. Be careful, since not all chiller manufacturers test to the same standards.

Key to chiller components:

2 -18" Condenser Fans
Chilled Water Return -- 1 1/2" N.P.T.
Water Level Sight Glass
NEW Electronic Controls with digital display

Temperature Set point
Return and Discharge Temperature Displays
High Temperature Alarm

Power Disconnect
Access Door
Water Reservoir tank fill -- 1/2" N.P.T.
Chilled Water Discharge -- 1 1/2" N.P.T

Chiller Specifications:
Model Number:	1250 AC
Capacity:	12.5 Ton
BTU Per Hour:	150,000 BTU/hr
Fluid Reservoir Capacity:	100 Gallons
Fluid Circulating Pump:	3 HP
Pump Specifications:	70 GPM at 38.0 psi
Voltage:	460/3
Amperage:	35.0
Cabinet Size: (W x D x H)	34 x 68 x 51 inches
Weight:	1750 lbs.

Caution:
Do not overcharge this, or any, refrigeration system. The refrigeration sight glass is only an indicator of coolant being in the system. The sight glass should never be filled when charging the system, and will always be fuzzy. Overcharging the system will damage the compressor.

For a quote or more information on the correct chiller for your application, feel free to contact T. J. Snow. We will be happy to help you out.

Units by the Ton:
½ | 1 | 1.5 | 2 | 3 | 4 | 5 | 7.5 | 10 | 12.5 | 15 | 20 | 25 | Control Panel | Sizing | Why a chiller? | Mold Controller
Welding Supplies | Return to T. J. Snow

Contact
Information: FAX (423) 892-3889
6203-6207 Jim Snow Way St.
P. O. Box 22847
Chattanooga, TN 37422 ORDER FAX (423) 490-2417
(423) 894-6234
1-800-NOW-SNOW

welders@tjsnow.com

Contact Information:	FAX (423) 892-3889 6203-6207 Jim Snow Way St. P. O. Box 22847 Chattanooga, TN 37422	ORDER FAX (423) 490-2417 (423) 894-6234 1-800-NOW-SNOW
	welders@tjsnow.com