T. J. Snow > Supplies > Chillers > 1/2, 1, 1.5 Ton Chillers
A Schreiber Chiller

1/2, 1, 1.5 Ton Chillers

(Air Cooled)

Need another size?

Need to figure out what size you need?

Do you know why you should have a chiller if you are resistance welding?

Features:

The unit is rated at the American Refrigeration Institute's National Standard of 95° F ambient and 44° F chilled water.
Energy Saving Design-- The unit will cycle on and off with varied load demands. No hot gas bypass.
Closed loop system eliminates contamination of the water system by recycling the water in a contaminant free flow path.
The Water Pump is bronze or stainless steel, and contaminate free.
Utilizes environmentally friendly R-22 refrigerant.
Ethylene glycol is not required for normal operating conditions. The unit will NOT be damaged due to an accidental freeze up.
Uses a world-renowned Tecumseh^TM compressor.
The Condenser is designed to allow full capacity at higher temperatures.
Energy Saving Design which does not use hot gas bypass.
Epoxy polyester powder coat finish is highly durable and environmentally responsible.
Time proven Schreiber Engineering name, and record of Superior Quality. In business since 1958.
Tested and approved by ETL Testing Laboratories, Inc.

Note about the Tonage Ratings:
The TrueTon^TM label assures that every Schreiber Chiller meets or exceeds its stated BTU performance as measured by the American Refrigeration Institute standard testing methods. Be careful, since not all chiller manufacturers test to the same standards.

Labeled Diagram of a chiller

Key to chiller components:

16" Condenser Fan
Water Level Sight Glass
Overflow
Chilled Water Return -- 1" N.P.T.
Dial Thermometer
Pilot Lights for the Compressor and Pump
Temperature Controller
Compressor Switch
Water Pump Switch
Access Door
Chilled Water Discharge -- 1" N.P.T.
Tank Fill -- 1/2" N.P.T.
Tank Drain
Pump Rotation Check

Chiller Specifications:
Model Number:	50 AC	100 AC	150 AC
Capacity:	1/2 Ton	1 Ton	1.5 Tons
BTU Per Hour:	6,000 BTU/hr	12,000 BTU/hr	18,000 BTU/hr
Fluid Reservoir Capacity:	20 Gallons
Fluid Circulating Pump:	1/2 HP
Pump Specifications:	20 GPM at 24.8 psi
Voltage:	115/1 - 230/1	230/1 - 230/3 - 460/3	230/3 or 460/3
Amperage:	30.0 - 14.0	18.0 - 11.0 - 6.0	11.0 - 6.0
Cabinet Size: (W x D x H)	26.5 x 32.5 x 34.25 inches
Weight:	400 lbs.	432 lbs.	460 lbs.

Caution:
Do not overcharge this, or any, refrigeration system. The refrigeration sight glass is only an indicator of coolant being in the system. The sight glass should never be filled when charging the system, and will always be fuzzy. Overcharging the system will damage the compressor.

For a quote or more information on the correct chiller for your application, feel free to contact T. J. Snow. We will be happy to help you out.

Units by the Ton:
½ | 1 | 1.5 | 2 | 3 | 4 | 5 | 7.5 | 10 | 12.5 | 15 | 20 | 25 | Control Panel | Sizing | Why a chiller? | Mold Controller
Welding Supplies | Return to T. J. Snow

Contact
Information: FAX (423) 892-3889
120 Nowlin Ln
P. O. Box 22847
Chattanooga, TN 37422 ORDER FAX (423) 490-2417
(423) 894-6234
1-800-NOW-SNOW

welders@tjsnow.com

Contact Information:	FAX (423) 892-3889 120 Nowlin Ln P. O. Box 22847 Chattanooga, TN 37422	ORDER FAX (423) 490-2417 (423) 894-6234 1-800-NOW-SNOW
	welders@tjsnow.com